
500-9041 v4.1
Welcome Report Control
Admin
Sys Config Tech-Ref
131
(or this software) outside of the schedule
(applies only if the authority is scheduled
above).
Elevators/Lifts and Floors: The "Manual Door
Command" selections apply to elevator (lift) and floor
control as well (if applicable).
- Escort Privilege:
Whether or not users
assigned to this authority will be considered as
"Escorts" (for use with "Escort-Required Visitors"
(to follow), and the "Escort" reader mode for
doors in the selected areas).
For details, refer to "Reader Mode" in the door
configuration section.
- Visitor (Escort Required):
With this selection,
the person is tracked as they 'badge' throughout
the facility, but access is not granted until a valid
escort's card is also presented.
To Block a Visitor from Using LCD Keypads: Locate
them in the 'Users' screen, and ensure their PIN is
blank.
Type of Cards that can Escort Visitors: This can be
changed as desired (the present setting is shown on-
screen in blue).
Related Topics:
Under "Account-Wide Panel
Settings", look for
"Setup ", then "
Escort-Required Mode
".
Turnstiles: The escort would typically have to 'badge'
a second time to let themselves in (antipassback not
supported for this application).
Escort/Dual-Custody for Readers: Escort mode is
also supported for all cards at specific readers.
"Visitor" cards are denied access at readers set for
"Dual Custody". Related Topics: "
Reader Mode
" in
the reader configuration section for doors and/or
elevators (lifts).
Misc: The 'visitor' setting is not available for escorts
(and vice-versa). As well, do not select "Master
Override" (previous/above)--as this will override the
visitor/escort feature.
-----------------------------------------------------------
Door Class
(within a Profile)
- In / Out of Schedule
, and
Class A/B/C):
These
settings restrict access to doors of a specific
'class' (A, B, and/or C), and/or optionally block
after-hours access to the specific areas (except
users with 'Master Override' authority). If
scheduled, a different set of door-classes can be
in effect when the schedule is active (In
Schedule) versus outside of the chosen
schedule (Out of Schedule).
For 'ordinary' scheduled door access, select "In
Schedule" A , B , C ; and "Out of Schedule"
None. For 24-hr access, either select
A , B , C for "Out of Schedule" as well,
or
set the
schedule to 24-hr.
Door class restrictions can also be customized for
individual readers.
Related Topics: "
Enable Class Checking
", and
"
[Class Map]
" in the reader configuration section for
doors and/or elevators (lifts).
Elevators (Lifts): This setting pertains to elevators as
well (controlled floor access).
If a user-schedule is not specified (i.e., Follow Area),
the selections remain in effect 24 hrs (subject to the
users' ability to access each area at a specific time).
Related Topics: "
Schedule
", previous/above.
-----------------------------------------------------------
Special
(within a Profile)
-Panic Token:
This designates associated user
'access tokens' as being a panic / duress
indication (instead of an access request).
In this case, the applicable 'access tokens' will
typically be separate wireless (RF) pushbuttons (with
appropriate detectors in the required areas). This is
typically used for areas such as parking garages.
- Wandering Patient:
Sets associated users to
be tracked as they approach exterior doors, or
other areas of concern.
With this type of 'user', the 'access token' will typically
be a wireless wristband (with appropriate detection in
door frames).
When the patient approaches, an alarm can be
triggered, and the door can optionally lock as they
approach. For details, refer to the "Special" tab near
the end of "Doors, Readers, and Related Settings".
- Reset Door Alarm:
Provides associated staff
members with the authority to cancel a
'Wandering Patient' alarm by presenting their
(applicable/compatible) token at the specific
door.
Comentários a estes Manuais